Skip to content
View in the app

A better way to browse. Learn more.

The Patriot Woodworker

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

What's On Your Work Bench?

Featured Replies

@Cisco Kid Very nice. How much does walnut cost where you live?

Edited by MrRick

  • Replies 2.9k
  • Views 386.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • PostalTom
    PostalTom

    Q:  Why does a chicken coop only have two doors?   A:  Because if it had four doors, it would be a sedan. 

  • John Morris
    John Morris

  • Still working on Urn, just finished glue up on top.  Will put a profile on it and sand it down then  off to finish room.   Dry fit:  

Posted Images

21 minutes ago, MrRick said:

@Cisco Kid Very nice. How much does walnut cost where you live?

Roughly $12 a board foot. A little more if you want wide stuff. A little more if you need 8/4. I got lucky with this last lot as there were some curly pieces in it once I ran it through the planer.

$9 a board foot for shorts, which can be a good deal if you don't need long pieces.

Thank you for the info @Cisco Kid

BTW...Welcome to our community!

Cheers!

MrRick

On 10/29/2026 at 12:46 PM, JimM said:

Carbs gummed up? Maybe some carb cleaner? I had a $90 lesson about that once.

Then ran mine dry every month with a cup or so of gas. Also used stabil and ethanol free gas.

They recommend running every 90 days to keep the warranty.

On 11/9/2026 at 6:49 PM, steven newman said:

Soon to be on my bench..

The 54th, out of the box   .jpg

Intend to use this as a Pattern...and build one of my own...

The 54th, Front of box  .jpg

$96+ change.....Stay tuned...

I saw one of the Harbor Freight ones once at auction going for over $100. Do your research, guys.

On 11/10/2026 at 5:26 AM, Fred W. Hargis Jr said:

There's a show on PBS called "A Craftsman's Legacy". An episode I happened to catch (I'm not a regular viewer, this was channel surfing) had him at the Gerstner facility going through some of the steps to make a Gerstner chest.

Gerstner factory is about 45 minutes from me and I've been there a few times and seen some of their videos. Some of them are now made in China and the ones still made here (at least the ones I saw) had plywood carcases. I was also a little dissapointed that the grain on the drawers was not matched up horizontally.

25+ years ago I rebuilt a Gerstner chest I got at a junk store. Basically I had to replace the entire outside carcase but for the drop front door, the top lid, and the cross piece between that lid and the door. It had been stored somewhere wet and fallen prey to dry rot and termites. I figure that would have taken at least 10 years and probably the chest was not new at the time so figure minmum of 1980's (though I think 1950's is more likely).

The carcase was mostly veneered plywood. I traded it a couple years later for a bandsaw.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.