Jump to content

  • Recent Topics

    Door Mode

    The boss says the weekend is over so it’s back to work. This is a phase of the project that is going to get tedious by the end but has to be done. The doors in this house are the standard raised panel doors that are pressed out of some material to look wood like. We will be replacing them all (18) with new doors made of Sapele. I am driving over to the coast tomorrow to pick up 700 bd ft of it in 4/4. 100 bd ft is for Static LV, another friend is going in for an additional 100 bd ft. It looks li

    Masonsailor
    Masonsailor | 
    General Woodworking 83

    A Project for May, 2024

    Looking around for ideas, found this one sitting in the dinning room window sill... Along with a writing desk...figured IF I change a couple details...like make the drawers 4" deep...and the sides into Frame & Raised Panel...hmmmm..   There is a Mystery board in the latest stash.. Is the 1 x 8...Ash..or...White Oak?   Them be Ray Flecks...   Have a few defects to work around... At least in the 1 x 6 shorts...and one end will need trimmed u

    steven newman
    steven newman | 
    General Woodworking 59

    Friday May 17th, 2024-What's on Your Weekend Agenda?

    Friday     Not sure how that happened.  Must have snuck up on me between the mow sessions between the rain sessions.  Weekend here looks like mow of the same.    What's on Your Weekend Agenda?   

    Larry Buskirk
    Larry Buskirk | 
    General Woodworking 5

    Customer service kudos.

    I normally stick to the wood turning forum but I just had an unbelievable customer service experience and wanted to give kudos  to the company. I bought an "Industrial Air" compressor at a local farm store in 2012. About a year ago the head gasket went so I bought a  3rd party rebuild kit and replaced it. Well, it blew again this morning. Rather than keep replacing it again and again I wanted to see if a new pump was affordable. Called the 800 number on my owners manual and the lady found what I

    Steve Krumanaker
    Steve Krumanaker | 
    Machinery, Tools, Research, Reviews and Safety 2

    OFF the lathe and just finished

    Just does not feel right to post finished work in the on the lathe post so I am creating this to post finished works. Please feel free to add yours. Walnut a friend gave me with Watco danish oil.  vase from my shelf with three carved feet. Aldo Watco danish oil. Spalted pecan.  Ruth Niles Can Tab Pull with I think Indian Rosewood and buff with Renaissance wax.  new design for phone amplifier in Crepe Myrtle. Lacquer finish

    Gerald
    Gerald | 
    Wood Turners 198

  • Information

    Who We Are

    About Us We are a woodworking community with an emphasis on sharing and learning the skilled craft of woodworking and all of its related disciplines. Our community is open to everyone who wishes to join us. We support our American veterans and active duty, being a veteran is not a prerequisite to join. Join us now! The Spirit of Our Forums First off you'll be a member of a very grown up group of woodworker's where drama is non-existent. Your discussion forum experience will be com

    John Morris
    John Morris | 
    Administrative Topics

    Our Mission

    Objective Of course just like most online woodworking communities we are centralized in the arts, crafts, and trades that are woodworking. But, we have another focus in our Patriot Woodworker community, we are the only woodworking community that was founded on our care and concern for our disabled veterans. Mission 1st To create an online woodworking community that is sensitive and respective of the men and women who are serving and have served in our United States Military.

    John Morris
    John Morris | 
    Administrative Topics

    Volunteer

    Volunteer The Patriot Woodworkers are an all volunteer community, from the staff and hosts who run our online woodworking community to the members who frequent our forums, you'll find volunteers in all of us. We are not on a payroll, unless you consider the spiritual rewards gained from volunteering, as compensation. How you can help If you are a woodworker, and if you want to help us help our American veteran and honor both our veterans and active duty, then look no further than

    John Morris
    John Morris | 
    Administrative Topics

    Education

    Education One of the many projects we are working on is a wiki for our online community. A wiki is a great way for woodworkers and enthusiasts to share their knowledge to others, and to impart their knowledge for others to learn from, and utilize as well for their own benefit. We hope you'll consider being a wiki contributor. Research Do you love researching? Do you like to write about subjects in a factual non-biased style? Do you like leaving your footprint of knowledge behind f

    John Morris
    John Morris | 
    Administrative Topics
×
×
  • Create New...