Popular Post Gene Howe Posted March 22, 2019 Popular Post Report Posted March 22, 2019 If your deal with that store works out, you may need to make a box joint jig. Sure would be faster and, it would keep uncle Charles at bay...at least in the hands. steven newman, Grandpadave52, FlGatorwood and 3 others 6 Quote
Popular Post steven newman Posted March 24, 2019 Author Popular Post Report Posted March 24, 2019 Hand made = $$$.....Had a "Me Day" today.....got meself out of the house, and did a solo road trip...Anna, OH....$5.... Small dividers, and a tap wrench....next stop...Hobby Lobby, for new Hardware Hinges, latches, and even some fancy feet brackets... Finally, Go Harbor Freight! $17 for four clamps....three 12", and a single 24" clamp.....the 24" is to replace that POS gray clamp that was fired.... Honey-do list when I got back home....seems the Boss has bought a "Shed in a Box"....guess who gets to build the dang thing.. Instructions leave a LOT to be desired.....methinks that +2:00 means two days....got the frames assembled.. And tied down.. I guess this counts as "shop time"? Now, I am too tired and sore, to even think about going to the shop... Maybe tomorrow, IF it rains all day, I can do a bit of woodworking? otherwise, I be outside, cussing up a storm ( and drawing a Rain Turtle..) Stay tuned.. Grandpadave52, Gunny, p_toad and 2 others 3 2 Quote
Grandpadave52 Posted March 24, 2019 Report Posted March 24, 2019 2 hours ago, steven newman said: Small dividers, and a tap wrench.. Sweet find and save. Dividers will clean up nice. 2 hours ago, steven newman said: Finally, Go Harbor Freight! ....$17 for four clamps....three 12", and a single 24" clamp +1...Never can have enough (H-F) clamps. You get any allocated space in the new shed for wood storage? FlGatorwood, Gunny, Cal and 1 other 4 Quote
steven newman Posted March 24, 2019 Author Report Posted March 24, 2019 Afraid there won't be any space for my stuff, other than ladders storage...got no floor in the shed.. New clamps are in the shop, box is out of the other clamps, been cleaned up, a top has been made to almost fit. A plywood bottom has been cut and glued in place, vise is holding things while the glue cures....even worked up a sweat in the shop! Waiting to see how much "help" I get today on that shed build.....before the rains show up.....film as I get it....may get ugly, today... p_toad, Gunny, FlGatorwood and 1 other 4 Quote
Grandpadave52 Posted March 24, 2019 Report Posted March 24, 2019 1 hour ago, steven newman said: before the rains show up Headed your way...been here about 1-1/2 hours or so. Gunny, steven newman and FlGatorwood 1 2 Quote
Popular Post steven newman Posted March 24, 2019 Author Popular Post Report Posted March 24, 2019 Rain Turtle worked.. Spent a bunch of shoptime, instead Bottom panel has been cut, beveled , and glued in place....Lid? Has been cut and fitted... Latches I bought yesterday..are a tad bit too big... Sides were sanded and planed smooth, even used a spokeshave to work on the front of the lid... Test fitted the feet brackets, and then used some big tools to install them... Compared to the screws I was using... Normal sized pencil. Hinges? After snapping two of those screws off, I remembered to WAX the threads...I also chucked a nail into the drill, and predrilled, lid was easy But, I needed helping hands to attach the lid to the case.. Lip on the lid in the vise....left these NEW H-F clamps on, while I installed the handles, as well... Remove the clamps, get out the stain and a brush...time for a PIP? Front view, shadow on the handle... Hinge side....and... Handle sides....thinking a box for Recipes? Waiting on the stain to cure, before the clear coat poly goes on....and, I can start on the second box.. Stay tuned.. Gunny, Grandpadave52, FlGatorwood and 3 others 6 Quote
Gene Howe Posted March 24, 2019 Report Posted March 24, 2019 Sweet box, Steve. What did you use to color the lid? FlGatorwood and steven newman 1 1 Quote
steven newman Posted March 25, 2019 Author Report Posted March 25, 2019 Same stain was used all over, including the lid.....camera and the shop lights sometimes have "issues" on how things show up...end grain came out a bit dark...as usual for end grain... FlGatorwood and p_toad 2 Quote
Popular Post Grandpadave52 Posted March 25, 2019 Popular Post Report Posted March 25, 2019 I like it...Nice touch with the lid handle and the decorative feet. Sign & date the bottom before the poly. Another Newman original. hatuffej, Harry Brink, steven newman and 2 others 4 1 Quote
Popular Post steven newman Posted March 26, 2019 Author Popular Post Report Posted March 26, 2019 Ok, cleaned that pair of 4" dividers up.....marked as Union Tool Co....hmmmm? Did a bit of resaw work, now have a sore spot on the hand from a kick-back.....that then bounced off the wall....was using a push stick....that is what hit the wall Picked through the stack, found 2 boards that at least matched each other...and spread a bit of glue... Will let this sit a day or so..out of the way....got the four sides for Box #2 cleaned up and flat...had an issue.. then does this with the ends and the sides clamped up...1/8" wider sides..Going to be one of "them days?" Laid out for the dovetail pins.. Hmmm...fun is about to begin...backsaw first. trying to split the lines.... Set up to do a bit of chopping....one chisel? Nah... Sized as needed... Dry fit..got to about here...was getting to the point something was going to get tossed against the wall.. Yeah, one of those days.. Decided to stop for the day...maybe tomorrow, I can get something done? Stay tuned Gunny, FlGatorwood, p_toad and 2 others 5 Quote
Grandpadave52 Posted March 27, 2019 Report Posted March 27, 2019 1 hour ago, steven newman said: Ok, cleaned that pair of 4" dividers up.....marked as Union Tool Co....hmmmm? No picture(s)...didn't happen 1 hour ago, steven newman said: Did a bit of resaw work, now have a sore spot on the hand from a kick-back.....that then bounced off the wall....was using a push stick....that is what hit the wall No pictures...doesn't matter...not good by any standards...GLAD you are OK and the wall took the "bullet" for you. Was it on the first pass through or after you rotated the board for the second (final) pass? 1 hour ago, steven newman said: Set up to do a bit of chopping....one chisel? Nah... That's a lot of chisels. Some of them look 1/8"-3/16" wide. Sorry the day didn't go well, BUT GLAD you're able to tell about it. FlGatorwood and Gunny 2 Quote
steven newman Posted March 27, 2019 Author Report Posted March 27, 2019 Hmmm.. Hmmm p_toad, Grandpadave52, Gunny and 1 other 4 Quote
Grandpadave52 Posted March 27, 2019 Report Posted March 27, 2019 But you needed this pair because you didn't have one that size or from Union Tool Co. Orange, MA steven newman, FlGatorwood and Gunny 2 1 Quote
steven newman Posted March 29, 2019 Author Report Posted March 29, 2019 Was too nice of a day Thursday, spent most out on the road.....Wednesday? a ROYAL PITA to do, even for two people working on it....weather was great...except the breeze did NOT help a bit.... Friday? nasty outside....may just be a decent day to hide out in the shop...maybe after Lunch? Stay tuned.. Grandpadave52, p_toad, FlGatorwood and 1 other 4 Quote
Grandpadave52 Posted March 29, 2019 Report Posted March 29, 2019 3 hours ago, steven newman said: a ROYAL PITA to do, even for two people working on it....weather was great...except the breeze did NOT help a bit.... Agreed Thursday was a nice day compared to the last couple of hundred. I too spent all day on the road including round trip to Indy...nothing productive done at home. Nice job on the shed...I've considered a version here, but after all the 50-60 mph winds we've experienced this winter in the wide open plains afraid it wouldn't survive. Several in the general area didn't make it this year. Living residential should give you a big boost for live expectancy. Hopefully, yard & garage sale season will open soon so we can return to fun again. Gunny, steven newman and FlGatorwood 3 Quote
Popular Post steven newman Posted March 29, 2019 Author Popular Post Report Posted March 29, 2019 Mid 50s outside, today....light, drizzlly rain all day long....thought i would hide in the shop, all day.....wrong....was told WE had to go to the stores, and the bank... Was able to get a little bit done, before that happened, though....laid out more dovetail pins.. Decided to try out the Hobby Lobby saw. As long as I keep the blade waxed from a candle, cuts decently enough, starts a lot easier than my No. 4 backsaw...hands do not like holding the handle and it takes twice as many strokes to make these cuts... can almost split a line, and leave some on both sides of the cut...Chopped halfway down.. Before I flip this over.. Pins are done! use these to lay out the tails...saw those, and chop.. Almost time for a dry fit? To see how much fine tuning I'll need Set this aside, and laid out, and cut the next set of pins...even had it clamped up, ready to chop Was told time to go.. may sneak back to the shop after a while....BTW, there MIGHT be enough left overs... To build a third one of these boxes? We'll see.. Stay tuned Harry Brink, FlGatorwood, p_toad and 3 others 6 Quote
Grandpadave52 Posted March 29, 2019 Report Posted March 29, 2019 6 minutes ago, steven newman said: Stay tuned Channel always on. I'm hoping I'm a lifetime member Glad you rustled up some more scraps...at least I know there's another project brewing in Sketch-up 1.0 Good utilization of yet another miserable day in the Midwest. FlGatorwood, steven newman and p_toad 1 1 1 Quote
Popular Post Gunny Posted March 30, 2019 Popular Post Report Posted March 30, 2019 4 hours ago, Grandpadave52 said: Channel always on. I'm hoping I'm a lifetime member Yeah about that, we need some more money for the Tires on the TPW jet. p_toad, steven newman, FlGatorwood and 3 others 2 4 Quote
Grandpadave52 Posted March 30, 2019 Report Posted March 30, 2019 1 hour ago, Woodbutcherbynight said: Yeah about that, we need some more money for the Tires on the TPW jet. Check's in the air-mail...oh wait, the plane is down...well can't say I didn't try. FlGatorwood, Gene Howe, steven newman and 1 other 4 Quote
steven newman Posted March 30, 2019 Author Report Posted March 30, 2019 Ugly day outside....whether to try the shop, or plop a DVD in.....may just put in a Fogerty CD and get in the mood.... we'll see... p_toad, Grandpadave52, Gunny and 1 other 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.