December 29, 20196 yr Popular Post comment_213863 Or, "Hide yer eyes, Mabel!" Added yesterday's haul to the 2 planks on hand.. There is 8 boards sitting there, average size...4/4 x 6" x 54". End grain? Has some fancy-schmancy grain, too... Might be entertaining to use? Counting the 2 boards I already had....about..$15 sitting here. Might last a while? May see how some match up, maybe a book-match? Stay tuned. Report
December 29, 20196 yr Popular Post comment_213867 36 minutes ago, steven newman said: Might last a while? Knowing you, Steven, it might last till supper Report
January 8, 20206 yr Author Popular Post comment_214811 Ok..now that the scraps are taken care of.....what to do with these 8 boards....may take a day or two off, and see about some sort of project I can cobble together....Supplier is "Down-under" til spring....so, what I have is what I have....4/4 x 6" x 54" on average.... This might take a while.... Report
January 8, 20206 yr Popular Post comment_214813 Got this from my Dad for Christmas. Drool people. Report
January 8, 20206 yr Popular Post comment_214816 1 hour ago, Woodbutcherbynight said: Got this from my Dad for Christmas. Drool people. I got a rock! Report
January 9, 20206 yr Author Popular Post comment_214944 Been watching a few NewYankee Workshop shows...and ...some of Roy Underhill's show...may buy some Pine for shelves, and a back for a case....Design work has started... Shaker Cupboard.... Steamer Trunk.... Lap desk...... Narrow Chimney Cupboard ( have a 12" x 12" spot beside the chimney...) Or...just another..Larger Table? With a drawer or two? Stay tuned to this "Batty Channel".... Report
January 10, 20206 yr Popular Post comment_214958 2 hours ago, steven newman said: Stay tuned to this "Batty Channel".... Don't start till tomorrow. After I get paid I can afford to get the popcorn this time. Edited January 10, 20206 yr by Woodbutcherbynight Report
January 10, 20206 yr Popular Post comment_214959 2 hours ago, steven newman said: Stay tuned to this "Batty Channel".... I vote chimney cupboard ( like I have a say, lol) but I'd like you to put some kinda fancy detail into it instead of just building it straightforward like you usually do Steven!! Report
January 10, 20206 yr Popular Post comment_214963 On 12/29/2019 at 4:03 PM, Woodbutcherbynight said: I'll get the beer this time. I think I'll make popcorn and have a cup of cocoa. It's a bit chilly here in Florida and we are about to get some nasty weather. Oh my, the apocalypse. Report
January 10, 20206 yr Popular Post comment_215016 11 hours ago, FlGatorwood said: It's a bit chilly here in Florida and we are about to get some nasty weather. Steve, I'll send you what's coming our way....6-12" of some crazy white stuff! Report
January 10, 20206 yr Popular Post comment_215027 24 minutes ago, Larry Buskirk said: Steve, I'll send you what's coming our way....6-12" of some crazy white stuff! Rather have a circumcision with a chainsaw. Report
January 11, 20206 yr Popular Post comment_215066 Awwww, schucks, Larry. Your kindness and generosity almost brought tears to my eyes. Report
January 11, 20206 yr Author Popular Post comment_215071 Have found a use for one of the 8 planks....Paul Sellers latest little class is called a desktop organizer....Will post a few pictures of the plan I downloaded.....details to follow....Just another fancy-schancy box, but.....it does have a drawer, and a lid...and quite a few dovetails to cut...hardest part? Getting my POS Printer to do it's job....might have taken almost as long as it will take this project to do...maybe... Stay tuned... Report
January 11, 20206 yr Popular Post comment_215105 Plans, Steve???? Did you're one celled sketchup blow a fuse? Report
January 11, 20206 yr Author Popular Post comment_215107 One Brain Cell Sketch Up is still working on what to do with the rest of the planks... Thought I would would give one of Paul Sellers' plans a try.....and see how it fits with the way I build things..... Even the best, well thought out, and drawn up plans...get changed when the first "shot" goes off...stay tuned... Report
January 11, 20206 yr Author Popular Post comment_215112 Moose and Squirrel has delivered The Plans.... Front view... View of an end...little 1/2 round lip is the drawer's handle.. Drawer details....Paul does a drawer a bit different than me.. A cutting list....camera didn't pick out some of the stuff... As for the plank to be used ( yes, just one..) Sorted through the stack.... Mainly for the grain If it isn't wide enough...we can do a glue up or 2 Stay tuned.... Report
January 14, 20206 yr Author Popular Post comment_215439 Well, cleared all the stuff off the bench...even put some things away Going to need a bit of elbow room... Thought I had grabbed the wrong saw....used it anyway.. A front, a back, and a board to make both ends....Disston D-8, 11ppi....seemed to cut better than the Atkins No.65, 8ppi did. Which left this thing. Not quite long enough for two parts...have to decide whether this longer piece will be a base, or the lid...shorter end will be in the scrap pile.. Hmm...Long enough...and, after I joint both edges, will be wide enough...however... Cutting list says it is suppose the be 11/16" thick....caliper says mine is 0.998" thick.....will need to plane it down a bit...later. Other 3 pieces? They are for a front, a back, and both ends. The front is to be in two pieces, one a drawer front. Edges are a bit rough, so..jointed the better of the edges, the ripped for width, just a hair wider than the plan calls for... Final width is 3-1/2"...including the 2 pieces for the front....reset the fence...first to 3-1/2" strong...then the front is split... Back, 2 pc front, and the board for the two ends...all have to match each other width wise. But..like the lid/base board..these are way too thick..they need to be 1/2" thick...reset the tablesaw again fence is 9/16" away from the blade, blade is up as high as it will go.. Almost 1/2 way up....ran the parts through.. Time I plane the one, it will be 1/2" thick. Thinner piece can be used to build the drawer? Lowered the blade a bit, to make ripping the narrow parts safer..some had a pile on the bench.. Plane this smooth, check the ends for square...about ready to cut the dovetails, and the groove... And see about building a drawer..might have a Poplar piece to make the floor of the storage compartment... And, I kept some thinner stuff for the drawer build.. Maybe? Taking a break for Lunch....will see how the rest of the day goes.... Stay tuned.... Report
January 16, 20206 yr Author Popular Post comment_215567 Kind of hobbled, right now.....right kidney has a 3mm stone....making the right side hurt....but.. Got some "Jointah" work done.. . Parts have been planed flat....ends squared up, the box's 2 end pieces cut to length of 5"... Parts stacked up...not sure which will be the drawer front.. Drawer front gets trimmed down to fit into the box....I did find 2 pieces to use as drawer sides, and the back... One side isn't too bad...the other is a bit rough.. Same 2 boards, just flipped over... waiting to hear when I see the Kidney Doctor....and get rid of that stone.. Stay tuned Report
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.