August 31, 20178 yr comment_122941 41 minutes ago, Dadio said: With the new improved glues, I have just held two pieces of wood tight for a couple of minutes and let set for an hour and when I broke them apart the wood gave loose and the glue held tight. Herb Good to know, Herb. Rubber bands are cheaper than clamps! John Report
August 31, 20178 yr comment_122943 3 hours ago, HARO50 said: Spread the glue to 3 molecules, then go over it with the shopvac. It will take off the top 2 molecules, leaving the exact amount needed! John I just KNOW someone is going to try this! It'd be easier to send the spreader back for re calibration. Report
August 31, 20178 yr comment_122955 39 minutes ago, HARO50 said: Good to know, Herb. Rubber bands are cheaper than clamps! John This pertains to small irregular shaped parts that are hard to clamp. Rubber bands work fine on small boxes with mitered corners. By using blue tape to align the miters, just fold together in a square or other closed polygon and tape the corners ,then put the rubber bands on to apply a little pressure. When I install small wooden handles on jewelry boxes, I find the center of the box ends and drill a small hole ,not all the way thru, Insert a round toothpick cut to length. drill a hole the same in the handle , put some glue on and insert the handle onto the toothpick and hold for a couple of minutes then let set for an hour. the toothpick aligns the handle and keeps it from slipping when pressed into place. Herb Report
September 15, 20178 yr comment_124736 After many years of woodshop experience I have come to be an avid champion of Bessy style clamps------yes very expensive but if interested in easy and satisfying clamping experience, these clamps are it. It all depends on what is important to one---I found that holding back on some recreational experiences quickly frees up the extra cash required.----- also after many glueup problems that most applications require only modest pressure Report
September 19, 20178 yr Author comment_125121 On 9/15/2017 at 11:32 AM, Marv Rall said: After many years of woodshop experience I have come to be an avid champion of Bessy style clamps------yes very expensive but if interested in easy and satisfying clamping experience, these clamps are it. It all depends on what is important to one---I found that holding back on some recreational experiences quickly frees up the extra cash required.----- also after many glueup problems that most applications require only modest pressure Recreational experiences?! For me, that would mean no internet or Xbox 360! I wouldn't be able to talk to you guys or save the world when you guys are safely sleeping!!! Report
September 19, 20178 yr comment_125123 1 hour ago, DerBengel said: I wouldn't be able to talk to you guys or save the world when you guys are safely sleeping!!! ah-ha!!! you talk to us in our sleep... that explains a lot... can't wait till my psycho babble expert hears that I really am hearing voices... Report
September 21, 20178 yr Author comment_125420 That was supposed to be 2 different thoughts but that reply sure cracked me up!!! Report
September 21, 20178 yr comment_125425 Don't know if anyone mentioned this but M & T are long grain to long grain joints that are structurally sound when glued together. If you force fit the tenon into the mortise you force most of the glue out and create a very weak M & T joint. As others said a light mallet tap should get them to slide apart with that in mind the glue will not be forced out but will properly set up on both surfaces and make the strongest joint (with some argument) that is known to man. Report
September 22, 20178 yr comment_125484 A little saying I read by I do not remember who " fit so that your hat will force it together" , that is a tap from your hat. Report
September 23, 20178 yr Author comment_125615 Your hat? That is a very light tap...can't think of much of anything that would go together with such a light tap. WOW. Report
September 23, 20178 yr comment_125617 The idea of the M&T joint is that it is rigid and the glue then holds it in place . Driving it together could well lead t early failure by crushing the wood or splitting the mortise. Report
September 23, 20178 yr comment_125754 18 hours ago, DerBengel said: Your hat? That is a very light tap...can't think of much of anything that would go together with such a light tap. WOW. If you wear a hard hat in the shop, you can give it quite a substantial whack! John Report
September 24, 20178 yr comment_125790 Beam clamps work when pipe clamps just aren't enough... In this case pipes were used and most destroyed because the threads aren't strong enough... Report
October 15, 20178 yr comment_128149 We ordered 12 -36" and 12 -48" just for parallam tops. Because Jorgensen beams are no longer anyone compared to Bessey I-beam clamps to Jorgensen? Report
October 16, 20178 yr comment_128244 Wow, Billy. That's a thick slab. Are those 1/2" pipes? Out of curiosity, what's the application for that glued up glue lam? Report
October 16, 20178 yr comment_128268 That's a chunk of money lying there! I'm curious, too! What is the final application? Report
November 1, 20178 yr Author comment_129820 Wish I could! lol Go for it and report back, with donuts! Report
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.