Estate sale finds

[Gerald]

Had a call yesterday from a Woodturner friend that the shop leftovers from a deceased club member was for sale. I called another member and hightailed it over. Paid 45 for the stuff on the table and 25 for the walnut. In only the Frued box blade and the Incra hinge jig is retail over 175. One box has some water based dye powder another a tap and dye set. Sanding discs, a monster turning tool . The green vise I have to do some research. And the push stick. 

 

[HandyDan]

Alright Blackbeard!  Nice haul.  The green vise looks to be a PanaVise.  I have the square base, the vise base and the two vises that I got at an estate sale also.  You're going to like it.  It is a great hobby vise.  There is a bunch of accessories can be had for it.  Here is a link to the site.

 

https://www.panavise.com/index.html?pageID=1&id1=1&startat=1&--woSECTIONSdatarq=1&--SECTIONSword=ww

 

[Al B]

Looks like you did very well !

[Gerald]

@HandyDan yep looks like that can be the beginning of a great relationship. Now like @steven newman have to make a box for it, maybe even use that box joint blade.

Edited June 27, 2020 by Gerald

[HandyDan]

13 minutes ago, Gerald said:

have to make a box for it

I let mine sit right on my work table.  Comes in handy too often to put away.  I wasn't sure the heavy square base plate was really part of it until I saw yours.  The bolt holes are perfectly drilled but the swivel base hangs over the edge and I didn't see it offered at their site.  Be sure to look around their web site.  They have many offerings not shown.  Electrical mounts and camera mounts to name a couple. 

[Gunny]

19 minutes ago, Gerald said:

@HandyDan yep looks like that can be the beginning of a great relationship. Now like @steven newman have to make a box for it, maybe even use that box joint blade.

You summoned him??? OMG did you run to store and get some alcohol??

 

Nice haul though 👍

[lew]

Nice haul "Bandit"  

[FlGatorwood]

Score, Bandit!

[Gerald]

6 hours ago, HandyDan said:

I let mine sit right on my work table.  Comes in handy too often to put away.  I wasn't sure the heavy square base plate was really part of it until I saw yours.  The bolt holes are perfectly drilled but the swivel base hangs over the edge and I didn't see it offered at their site.  Be sure to look around their web site.  They have many offerings not shown.  Electrical mounts and camera mounts to name a couple. 

I looked to see what this stuff costs and I also did not see the plate. I have one ball mount I also could not find on  site. It has a shaft apparently for mounting , with a slight grove and a screw in the middle of that. The shaft is slightly pover 1 inch and has a hole in it slightly smaller than the hole in the ball mounts.

   I also kinda wondered about the way that plate overhangs and why is there hat flat on one side.

   The cost of the ones in the site I have is $222 but plus the two not listed probably over 300 . I had no idea, and the site calls all these heavy duty.

[HandyDan]

2 hours ago, Gerald said:

I looked to see what this stuff costs and I also did not see the plate. I have one ball mount I also could not find on  site. It has a shaft apparently for mounting , with a slight grove and a screw in the middle of that. The shaft is slightly pover 1 inch and has a hole in it slightly smaller than the hole in the ball mounts.

At the site these links to the left show many more pieces.

 

[Gerald]

@HandyDan I looked thru those and did nor see the two pieces.

[Danl]

A very nice score for sure!

Danl

[HandyDan]

21 hours ago, Gerald said:

I also kinda wondered about the way that plate overhangs and why is there hat flat on one side.

 

I got the above picture from an old catalog I found.  They didn't have as many choices as they have now.  It also shows the square plate.  I would bet the mounts with the three tabs would fit the plate nicely.

 

I found the catalog at Vintage Machinery.

http://www.vintagemachinery.org/pubs/detail.aspx?id=23373

 

 

Here's the catalog pdf link.

http://www.vintagemachinery.org/pubs/11562/23373.pdf

 

 

 

 

 

[Gerald]

5 hours ago, HandyDan said:

 

I got the above picture from an old catalog I found.  They didn't have as many choices as they have now.  It also shows the square plate.  I would bet the mounts with the three tabs would fit the plate nicely.

 

I found the catalog at Vintage Machinery.

http://www.vintagemachinery.org/pubs/detail.aspx?id=23373

 

 

Here's the catalog pdf link.

http://www.vintagemachinery.org/pubs/11562/23373.pdf

 

 

 

 

 

Thanks Dan , the piece I could not find is called a up down converter. Problem now is need a 1 1/8 id tube and a clamp to use it. Might be able to build something in wood to hold it in bench vise.

[HandyDan]

12 hours ago, Gerald said:

Thanks Dan , the piece I could not find is called a up down converter

There is a lot of Panavise on Ebay but I didn't see what you need.  The stuff on Ebay sells for new or nearly new prices.  There are a few deals though.