October 1, 20178 yr Popular Post This started out as a 8" x 8" x 2" piece of poplar. After that, the picture pretty much tell the story. It is intended for use as a fruit bowl, hence the green rim. That, by the way, didn't go as expected. I purchased a green paint pen from Hobby Lobby, intending to hold it against the rim with the lathe on its lowest speed, but the pen was the type that you have to keep depressing the nib on the end to pump the paint to the tip. That, of course, didn't work with the bowl turning, so I would up having to pump some paint to the tip, get it on the rim of the bowl, and actually "draw" it onto the rim, while periodically turning on the lathe to even out the application. It eventually worked OK, but next time I will figure out something different.
October 1, 20178 yr I like the idea of the green rim, I haven't found a good way to add opaque color while the lathe is spinning and your way seems to have worked pretty good. Steve
October 1, 20178 yr I have used Crayola paint markers in the past on some ornaments. Worked okay but did bleed some if not careful when applying finish. Best to make your edge a burn line. It is a nice looking bowl. Dan Edited October 1, 20178 yr by HandyDan
October 1, 20178 yr Author 1 hour ago, Steve Krumanaker said: I like the idea of the green rim, I haven't found a good way to add opaque color while the lathe is spinning and your way seems to have worked pretty good Well, I didn't actually apply the color with the lathe spinning. I had to apply it while stationary, then turn on the lathe to try to even the color out. That sorta-kinda worked, but it was tedious.
October 1, 20178 yr Author 1 hour ago, HandyDan said: Best to make your edge a burn line. It is a nice looking bowl. Thanks. BTW, what is a burn line?
October 2, 20178 yr Hold a wire or string tight against the edge where you want the mark and it will "burn" a line into the wood.
October 2, 20178 yr It's really easy to make a burn wire- Using round balls on the ends is a little safer in case the wire would catch. I made mine with a piece of dowel on each end. The wire can be something line 18 or 20 gauge steel wire from the big box store. Better yet, if you have any old guitar or banjo strings, they work perfectly. I usually use the skew chisel to cut a small groove- to capture the wire- then hold the wire against the spinning workpiece. The friction will cause heat and burn a line.
October 2, 20178 yr Author OK, so now I get what a burn line is, and how to do it. Referring back to @HandyDan's post, how does it help with adding paint? Does the burn line seal that edge and prevent the paint from bleeding, or is it just a good visual reference to aid in applying the paint? Or, maybe all of the above?
October 2, 20178 yr 2 hours ago, PostalTom said: OK, so now I get what a burn line is, and how to do it. Referring back to @HandyDan's post, how does it help with adding paint? Does the burn line seal that edge and prevent the paint from bleeding, or is it just a good visual reference to aid in applying the paint? Or, maybe all of the above? All of the above. Burn lines without paint add nice accents too.
October 2, 20178 yr Popular Post 2 hours ago, PostalTom said: OK, so now I get what a burn line is, and how to do it. Referring back to @HandyDan's post, how does it help with adding paint? Does the burn line seal that edge and prevent the paint from bleeding, or is it just a good visual reference to aid in applying the paint? Or, maybe all of the above? I'm not certain there is a "right" way to do it but this is what I do- Apply the paint as neatly as possible (there's always some that's not where you want it. When dry, use the skew to create a tiny capture cut at the edge of the painted area. Burn the line. Use sand paper or scraper or tool of your preference to remove the errant paint from the "other" side of the burn line. Although I didn't burn any lines on this piece, I did use this process. The texturing was painted completely then the high spots were sanded and finally a scraper was uses to cleanup the inside and outside ring borders
October 2, 20178 yr A second thought on color besides the burn line to control bleed. You might try acrylic with lathe very slow. Also on the Clewes platter he does not color all the way to the edge and uses a sharpie to color the edge black.
October 7, 20178 yr Author Thanks everyone for all the kind words. I thought the bowl was kind of basic, but the encouragement is always welcome.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.