steven newman Posted August 3, 2016 Report Posted August 3, 2016 Decided to at least get them milled down a bit. One edge has been jointed The plane is a Stanley No. 7c, type 9. For some reason, it looks a bit tiny....edge of the board is 1-1/8" wide, by.... 50-1/2" long. Wider end is about..16"....The $1 slab of walnut does have a bit of cupping going on, though.. So, I might as well rip right down the center. Then surface all four edges. There is a slight bow along the length, might make a cut across the middle, as well. I did try out a Junior Jack on that edge.... Might have set it a wee bit deep? It looks very small, sitting on the edge... Plane is a Millers Falls No. 11. When I get back down to the shop, I'll start cutting this thing into a few pieces I can use.....One of two planks I picked for a $1 each.... John Moody 1 Quote
lew Posted August 3, 2016 Report Posted August 3, 2016 Mighty nice piece of walnut for a buck! steven newman 1 Quote
John Morris Posted August 3, 2016 Report Posted August 3, 2016 I like the price Steve, even if it is cupped, there is plenty of great walnut that can be used for all sorts of projects. A dollar well spent. steven newman 1 Quote
John Moody Posted August 3, 2016 Report Posted August 3, 2016 Awesome piece of Walnut and for a $1.00, wow!! steven newman 1 Quote
steven newman Posted August 7, 2016 Author Report Posted August 7, 2016 Going to be a few days before I can do anything more in the shop. Wrong meds last weekend built up to a "heart attack" like symptoms.....Wound up getting a heart catherization done wednesday. Got home yesterday. Very sore, and very restricted as to how much I can do right now. No stairs means no shop time, same with no lifting, or driving. Have to wait on the hole in the leg to heal. Always something....been a bad year... Quote
lew Posted August 7, 2016 Report Posted August 7, 2016 Take it easy. Shop time can wait. Your recovery is the most important thing. Quote
Gene Howe Posted August 7, 2016 Report Posted August 7, 2016 40 minutes ago, lew said: Take it easy. Shop time can wait. Your recovery is the most important thing. A big DITTO. steven newman 1 Quote
steven newman Posted August 14, 2016 Author Report Posted August 14, 2016 Not too sure that slab IS Walnut......did a clean up, and resaw of a few boards.....looks more like .....Cherry. Surfaced all four sides. Wanted it square for a reason... 1/2" thick to make a Book Matched pair... There are the black inclusions, like cherry. The bandsaw smoked the shop up, with a NON-tannin smell.....more like a bunrt Cherry pie... Yep, Fake Figure. More of where the sawmill went. Once I had smooth planed it down.....rather plain grain. But it is a red colour. Well, one down three to go.. So, it would seem I have about..5 bf of Black Cherry sitting here. That I spent a dollar bill on. As soon as the Dungeon Shop dries out again, and a Brown Bat quits flying Air Patrols overhead, I might make something out of these things... Harry Brink 1 Quote
lew Posted August 14, 2016 Report Posted August 14, 2016 15 minutes ago, steven newman said: I might make something out of these things... Bat annihilator?? I recently had a chunk of really dense unknown wood. It wasn't until I cut it that the "aroma" told me it was cherry. steven newman and John Moody 2 Quote
steven newman Posted August 16, 2016 Author Report Posted August 16, 2016 Well, second board has been S4S, and resawn... A little shorter. With a few shavings laying around. Yep there is a crack in the one. Might have to work around that, or just glue it back in place. Both panels are about 8" wide.. Still have two more boards to work over....Can't wait to see what they will look like....and..they are 6" wide.....5 bf for a dollar bill, of Cherry. Not too bad? John Moody and lew 2 Quote
John Morris Posted August 16, 2016 Report Posted August 16, 2016 Are those machining waves in there Steve, or is there some figure in that thar lumber! steven newman 1 Quote
steven newman Posted August 17, 2016 Author Report Posted August 17, 2016 A little of both. And, IF I let them sit out like this too long, they redden right up. There isn't any machining, other than the bandsaw, and the handplanes...Need to find my bottle of Elmer's, and make a couple panels out of these.... Quote
steven newman Posted August 17, 2016 Author Report Posted August 17, 2016 Need to bring in the other slab...been leaning up against the house since I brought it home..debate is now where to crosscut that 7' long chunk to where I can work with it. Lots of live edge and a couple BIG knots going on. Might be a bit rough to resaw down from the 8/4" thickness. Maybe rip the live edge off, and reuse elsewhere? Then I could resaw the slab a bit thinner? Maybe more book matching? The first two slabs? Thinking either a finger jointed box and lids? Maybe set them outside in the sunshine for a day....once it ever stops raining. Quote
steven newman Posted August 18, 2016 Author Report Posted August 18, 2016 Well, that didn't go too well......New blade in the bandsaw....1/4" wide one does not play nice, even brand new. May just use what is already milled and planed flat as a start on a box.....I can use the wavy stuff as filler. Cut those down a bit, to make using them a bit easier. Found an old piece of Cherry I've had in the shop for a long time......colour and grain matches this new stuff Let's see...slab was just over 5 board feet, spent a dollar bill on it. so.....about $0.20 a board foot? I can't get too worked up about a few miss guided cuts. Will have to see what the 7 footer will yield, as well. Maybe a stand of some sort? Bandsaw blade was even shedding a tooth or two.....May have to go back and buy the 1/2" wide one, after all.... lew 1 Quote
John Moody Posted August 18, 2016 Report Posted August 18, 2016 Some really nice looking grain in the walnut. Can't wait to see what you do with it. steven newman 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.