Search the Community
Showing results for tags 'holder'.
Found 14 results
-
Made this today, based on pictures of others i found on the web. there is a commercial one that sells for $509. this was considerably less than that. upper bin is for a pistol, bigger bin is for rifle/shotgun.
-
A slow week here in our turner's forum. Our Patriot Turners- What’s Coming Up- Click on the following images for links to more information- From the AAW- For The Newbies- Sanding our turnings is time consuming. Changing disks on the Velcro sanding pads just adds to the delay. I know @Gerald has a sanding disk for each grit and that can save some time. It also saves some wear and tear on the Velcro. Here's a video showing shop made sanding disk holders- Wooden scoops are always a nice addition to the kitchen. Here Richard Raffan shows us how he does them- Check out his YouTube channel for more turning videos- https://www.youtube.com/channel/UC2tEGrCP1GiVwfaT4K9bcNw Tracey Malady demonstrates the versatility of the Easy Wood Tools, @Jim from Easy Wood Tools, carbide cutters as she turns finials- Expand Your Horizons- A neat tip from Lyle Jamieson on how to keep lighter colored sapwood from darkening- Alan Stratton demonstrates some shop made jigs for creating turnings with eccentric patterns- Our local PBS station is always a little behind the rest of the country, especially when it comes to woodworking shows. This past Saturday, Jimmy Clewes was featured turning his signature platter. The episode is available for purchase at- https://www.woodsmithshop.com/episodes/season15/1511/ New Turning Items- With the Virtual AAW Symposium taking place, I am hoping there will be some new turning tools/equipment introduced. Guess we will have to wait and see. Everything Else- Rick Turns list of YouTube woodturning videos from last week- In preparation for each week's "Wednesday's...", I spend some time searching for informative videos. Some come from YouTube. I noticed recently that the YouTube users rating system seemed different. The "Thumbs Up" choice is listing the number of positive responses. The "Thumbs Down" choice doesn't show any negative votes. Thinking this was a little odd, I went searching for the reason. If you are interested in understanding the change- https://youtu.be/f1Izh3-c88Y Could this be a carryover from the "everybody gets a trophy" generation?? Safe turning and stay well
-
charger holder for new drill/driver
-
Hey folks, I have these small rounds of wood pieces that came from an old wooden viking bowling set. they are angled at the top. I'd like to keep this feature but when I start the hollowing Process I run into a lot of catches, even after I drill center of the piece. Any ideas could I possibly use forsener or small spade bit?
-
Just when I thought I saw the light at the end of the tunnel, I realized it was a long freight train heading in my direction... Our Patriot Turners- @Gerald Showed us a hollow form to which he added color. He received lots of questions and compliments about this piece. Please check out his post and see how he did this- @HandyDan shared a really neat design he found. If you have ever struggled with moving you lathe (or any heavy piece of shop equipment) this might just be the ticket. Check Dan's post for additional concepts- Last week's post, from @FlGatorwood, concerning the skew heel vs. toe discussion generated lots more comments. If you missed the post or want to see what others had to say- @Ron Altier gave us a heads up on a really cool video. Lots of turning being shown, as well as other types of woodworking. What’s Coming Up- The Rocky Mountain Woodturning Symposium is coming up! September 13th- 15th. Click on the above image for the link to more information and registration. For The Newbies- @Gerald provided us with a link to a nice sanding disc holder. Check out Gerald's post for the link and some of the comments- If you are thinking about buying a lathe, Mike Peace posted a video that may help you. Expand Your Horizons- Off center turning can create some really interesting shapes. Sam Angelo demonstrates turning a teardrop shape. New Turning Items- If you have a "Work Sharp" machine and wanted to be able to use CBN sharpening wheels, you are in luck!! The folks over a Woodturners Wonders now have just what you've been looking for!!! Two sided discs in various grits. Check them out at- https://woodturnerswonders.com/collections/cbn-discs-for-work-sharp Everything Else- Rick Morris (Rick Turns) recently moved into a new shop. In this video, he shows us that even a new shop can't prevent Edward Murphy's Law from being applied- Safe turning
-
This LINK takes you to a method to make holders for sanding discs for your drill. I will add to this you will need to add a pad to the holder and velcro . For gluing the pad ( garden knee foam works) on Shoe Goo works very well. For the velcro use either plain back and glue on or self adhesive. Also I shape mine with the wood being smaller than the sanding pad and then shape the foam on the lathe with a skew , kinda like a little funnel shape.
-
Bailing wire was once was considered the best known method responsible for the making the American west. Today that has changed by the advent of Duct tape, Super glue, Velcro, as wood crafters Hi tech screws & biscuts. But below I have a helper to act as a second pair of hands for the guy that works by himself in a wood shop, that makes boxes into anything. These supports are similar to those my Grandfather had. The dimensions for each bracket are 3" wide 7" long and 7" tall and made from 1/2 Baltic Birch ply wood as my preferred material for shop jigs & fixtures, for the most part. A base accepts two supports, and is the same width and twice the length (1/2" x3" x 14"). You can go longer but for storage sake I saw no reason because you have so much adjustment. You can leave a tail if you want to clamp the fixture to you work table. My work tables are replaceable so I screw a lot of my fixtures directly to the table. When I get real anal retentive I use a spoil board to attach the fixtures. The base has 4 holes in it. Two of which hold in my case 1/4" " Tee nuts which the first bore in sequence is a counter bore so the t nut will be more than flush with the bottom. In this scenario the counter bore is 3/4' diameter and 3/32" deep centered 2" in from the end. A second pair of "T" nuts can be added down the line but I never found that necessary. The "T" nut holes center treadled shaft required a 5/16" bore to be bored in the center of the "t" nut counter bore. I used a fence and a stop for the counter bore in the same setting for both. I then placed the stop in 1" with the 5/16 bit to bore holes on each end to hang the finished fixtures for storage. Because I am the way that I am a slight counter sink bit cleaned the holes with a slight chamfer. The photo below shows the bases top & bottom. On the supports box joints were used in the 90 degree corner and a 1/4" dado runs parallel the length 1/4" deep and 1/2" in from the edges to accept 1/4" birch plywood corner bracing to maintain a 90 degree angle. A single 1/4 slot is created centered and about 1†from each end it is stopped. This is done on half the support arms to facilitate the adjustment knob & bolt for adjusting the supports in & out. It is a easy task on a router table with stop blocks. A ¼ hole was bored in the path prior as a starter hole. Once the material is finish milled a dry fit is to routing is made. Make double sure in the dry fit process all your joinery is consistent and accurate. The assembly would be matching the two support pieces aligning the dados. Glue is put in the corner joint and the dado. Place the 1/4 ply angle supports in the bottom dados inset about 1/8 from the edge where the corner comes together. Now draw the two support pieces to form the 90 degree angle with the upright of the corner to enter in its dado mate. Remember I said the lower one is only about 1/8 of an inch from the end of the support? That wont allow the support arm pieces to seat into their corner purposely. This is so when you clamp the corner into fit the plywood is firmly and completely seated in that dado. Working in your glue up time, make sure all is aligned and you have solid seated joints. Check the 90 degree angle with a square and make adjustments as needed. This is not the time find your milling is sloppy so make double sure in the dry fit process all your joinery is consistent and accurate. Once I find the support arm is square and all is in place I toe nail a pin front & back, top & bottom of both the angle bracket where it meets the dado penetrating the bracket and the support arm. After assembling the support arms turn your attention to installing the two nuts into the counter bored holes. This production used ¼ x 2 carriage bolts, washers & ¼ threaded mini knobs. The bolts are threaded through the top of the mini knob completely, and a washer is placed over the other end of the bolt and the bolt is inserted through the slot and threaded deep enough to sufficiently garb but not protrude beyond the base bottom side. Now you can use your preference of corner clamps to handle the task at hand. My final thing would storage of these awkward devices. Remember the other holes that I chamfered with a countersink bit, on the ends of the base? They hang like ducks in a row. By Brad Vickery copyright.
-
The story behind this little "What is it", is that I had this 1/2 log piece that came with the lumber stash,pic1. I didn't know what kind of wood it was so I cut a about 6" off the end to clean up and see what I had. It turned out to be Maple. I didn't want to just throw away the piece so thought I would make a band saw box out of it. So I cut the bottom off, cut out the center, glued up the sides and reattached the bottom. The cut on the bottom looked ugly so I made a molding and then made some feet for it and called it a desktop pencil holder. The finish is 2 coats of spray shellac, and 6 coats of water based poly thinned 50/50 with water. I did stained the base/feet ,because it looked better next to the bark. Herb
-
Picked this "gem" today while on a rust hunt....yes I found rust, too... That is the blade that was with it. There is a thumbscrew to tighten things in place... It has a smooth, curve "bottom" Those "teeth" on the blade are not from a breakage.. They have been filed that way. The only markings seems to ba a "Patented DEC (#) 15......as in Dec of 1915. The "day" part is a bit scratched up. One other edge is straight (almost) and the other has a slight curve to it. Thumbscrew seems to match a Stanley made one. What is it?
-
I lost a lot of my hearing during my stint in the Navy, working around jet aircraft. Now I wear hearing aids. The batteries tend to die when you need them most. I turned this little holder for my key chain. Made from Walnut and Maple.
-
See the tilt differences? IT's supposed to keep the littler tools from spinning out What lathe tool carousel picture would be without a Where's Waldo picture with the wood carousel lost in wood clutter? If you can find it in the first thirty seconds of looking you win a prize. It's an a ll expenses paid dream vacation to the mists of Avalon long ago and far away. You even get to have dinner they Mordred and Morganna
-
From the album: Ring Tray's
A bit wider view of the piece. I still have a lot of sanding to do but here it is -
From the album: Ring Tray's
This ring tray is made from Birdseye maple and curly maple. I tried to get a tighter shot of the grain, I hope it worked. -
Had some scraps laying around (still) and wanted something to put a set of chisels in. Had some 1/2" plywood, drilled a few holes, then made a slot into each hole. Forstner bit and a scrollsaw. Power tools weren't done, just yet. Wanted to roundover the slots. Router table was still set up, so That is the $3 router, hanging from a $20 table. Ok, holder is started. Used a piece of barn wood fir to make the two sides, and cut a dado across in the middle. Just wide enough for the holder to slide in. Router bit? Ah, nope. Had an old school tool This is a Disston No.7. Seemed to make a few decent cuts. Knocked the waste out with a 3/8" chisel. Used a couple other chisels to cut a stopped dado at each end of the base. Base is a 1x4 scrap of pine. That "dado saw" cut it to length. Marked out where the stopped dados were to go, and chopped them out. Used a rebate plane to cut a rebate along the back side of the base. Base was about done, I did run the front edge on the router table. Now a bit of assembly work. Nails, glue, and a clamp While I had it clamped up, I nailed a back onto it. base did fit, but needed to be a bit flatter, to sit on a benchtop without falling over. Got out a handplane to dress the bottom flat Checking with a square until done. Some of the shavings were a might thin. That is a $1 jack plane. Ok, everything together? Time to "Load'em up!" another look.. Nothing real fancy, chisel wise. Just a means to organize them a bit, rather than just toss them in a drawer. Rack will go into Tool Chest #1, as soon as i can get in it...might have to build a stand for the router table?
