Skip to content
View in the app

A better way to browse. Learn more.

The Patriot Woodworker

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The Big Project

Featured Replies

In preparation for cutting the large sign, I'm working on a smaller piece, 12" x 24" , cut from the same sheet of plywood.

This will allow me to familiarize myself with spiral blades I'll have to use on the larger sign ( 24" x 36"). I'm using FD "New Spiral" #3 blades for these two projects. The New Spiral blades are made from flat blades with teeth milled on both sides of the blade. The smaller project will allow me to extrapolate the number of blades I'll need on hand to finish the cutting.. I'll order a couple of dozen blades over the quantity that I think I'll need, just to be sure.

I've learned how to have my graphics program (Inkscape) measure the total inches of lines in a pattern. I've guesstimated the number of blades I'll need for the small pattern and used that number to guesstimate the number to cut the larger pieces. I will firm up those numbers as I cut the smaller piece. But it's a start.

The smaller piece:

20261022_220412.thumb.jpg.685c1c113680a9fb2b79622609d6c952.jpg

Good thinking on the testing. Did you find it hard to learn Inkscape?

  • Author

The basics in Inkscape were okay, but some of the stuff made me pull hair out.

The newer editions are easier to learn.

The major concern for me is I can't print 11 x 17, I can open the file with Libre office and print, but Inkscape... nada.

  • Author
9 minutes ago, lew said:

Will this help?

No, there is some technical issue between my HP printer and Inkscape. That file I just tried to print, closed it in Inkscape and opened it in Libre Office (Draw) and it printed from Draw, from Inkscape... the printer makes noises but does not print, when I forced it to print, don't remember the exact sequence, it printed the file as an 8.5 x 11 image on an 11 x 17 paper. All the Inkscape guru's say the same thing, "convert to a .pdf and use another program to print". Still it's free software so...

Edited by Wichman3

  • Author

All the cutting is done on the smaller piece. 8 1/2 hrs total. 1/2" plywood, FD New Spiral #3 throughout. Still need to put a finish on it. 😊

image.png

Edited by Wichman3

  • Author

I needed extra supports to the sides of the panel. I had this in mind when I first got this miter saw stand, and I'm finally putting it all together. 😀

A square hole in a 2 x 4 for the extra supposts:

square hole.jpg

The support installed in the square hole:

bracket installed.jpg

The saw with the two aux supports:

saw with aux supports.jpg

  • Author

A few pictures of the process:

To install the blades in a large panel, such as this, I need three hands, the third hand is a small spring clamp to hold the blade while I maneuver the panel with two hands:

blade clamped.jpg

I got lucky on this one; the panel just fits on the saw so that i can reach the furthest point to cut.

front arm clearance.jpg

and the panel just clears the back of the arm so I can cut:

back arm clearence.jpg

5 hours ago, Wichman3 said:

and the panel just clears the back of the arm so I can cut:

That is close!!

  • Author
42 minutes ago, lew said:

That is close!!

Yep! I could cut with 20" of panel in front of the saw ( I've got a bunch of weight hanging on the stand, and the roller supports can go up front quite a bit ), but his is much easier. 😀

  • Author

A couple of photos on my setup.

A new side support with the rollers at 45 degrees. The weights added to the side extensions of the miter saw stand ( helps keep the saw and stand from being tippy ).20261104_001219.jpg20261104_001210.jpg

20261104_001139.jpg

  • Author

A lot of cutting the oversize piece is by guess and by golly. Years ago I read an article of a woman who was cutting large panels, her husband built a table that sat astride the scroll saw without touching it, so that none of the viration of the saw transferred to the piece being cut. But, I haven't seen anything else like this. Just call me InZane (my middle name IS Zane, so there you go).

The roller arm were rocking too much so I added set screws to hold the arms in place. I have some 1/4 x 20 thread machine screws and a tap and die set. I drilled an undersized hole and tapped it for the machine threads, this isn't structural so I think the threaded wood will be enough.20261104_220836.jpg

  • Author

4 1/2 hours of cutting; guesstimate for the project; 10 hours

4.5 hrs.jpg

  • Author

If you know that it's going to take a while, it helps to prevent rushing. 😀

By now you're in a groove, the rest should come along nicely.

  • Author

6 and a half hours of cutting. The detailed graphic is finished, the rest is large letters and should go faster. 😀

6.5hrs.jpg

So is the 10 hour estimate still good? (it looks really nice, BTW)

  • Author

So far, so good 😊

  • Author

Nine hours in:

9 hours.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.