Search the Community
Showing results for tags 'installation'.
Found 2 results
-
My son’s microwave quit working and he wanted to purchase a new one. The old one hung above his stove and that is where he wanted the replacement unit to be installed. I advised him to purchase the same make/model I had, and I would help him install it. I purchased a GE unite 1-1/2 yrs. ago. It is a low-end unit because my wife only wanted on/off and high for mode options. While he was at the box store he called me and asked if he needed to purchase anything else to aid in the installation. I informed him that everything needed was in the box. I went to his home today, moved the stove, pulled down the old unit, eyed balled the hanging bracket location, and asked him to get the new hanging bracket from the box. No can do. There wasn’t a bracket in the box. I pulled out the manual and it clearly indicated that the bracket was not in the box but was needed. All the bracket attach hardware were in the box. I asked my son to look up the part on the internet so that we could purchase one from a store that had it in stock. No can do. GE has removed the needed bracket from the included items, and you have to purchase the bracket on-line. So, make two trips and wait. But that is not the worst. The bracket is being sold for $130. What a marketing ploy. Reduce the price of the microwave and gouge the consumer for an item they must have. This whole thing stinks. Danl
- 14 replies
-
- 8
-
-
-
- general electric
- ge
- (and 3 more)
-
Well, a couple weeks ago our tub drain sprang a leak upstairs, it's the kids bathroom. Small bathroom about 5 feet wide by 10 feet long. The tub is at the end of the bathroom, an alcove type I guess you could call it. The water has been soaking into our downstairs ceiling some time now, for who knows how long, finally the drain gasket gave out completely and a tub full of water poured into the ceiling, and forced me to open up the ceiling and discover mold and damage. Called the insurance company and they would have nothing to do with it, because there is mold in the downstairs ceiling, it's assumed it's been going on for a long time, and it's deferred maintenance that we should have performed, but, I had no idea it was leaking! So, this extensive water damage, has lead from one thing to another, and I just ended up gutting the kids bathroom completely a couple weeks ago, and we are going to give them a new one. So I cut the old dingy fiberglass surround in three pieces, and took it out, and I gutted the rest of it, vanity gone, toilet gone, floor tile gone. Today we went and got the tub, we were wavering between cast iron and steel, the fiberglass just gets dingy after a decade and looses it's luster, I have seen 50 year old cast iron tubs look as good as new. After much investigation, we decided on a compromise, a tub Made in the USA, called Bootzcast. It's a steel tub, porcelain coated, and it weighs 88 lbs, instead of the massive 365 lbs for the base line Kohler cast iron. I love the quality of the cast, but it's just heavy, and we have a small bathroom, hard to menuever in. I really like this Bootzcast, it feels just like cast iron when you knock on the sides, it's thick, and dense sounding, has a 1" to 2" layer of foam coating the outside, so it's really insulated like a cast iron tub is. But again, light on the back! And we get the benefit of it being steel with porcelain, a nice compromise I feel. So, sorry for the long winded explanation, but the tub has the flange that you are suppose to nail off to the studs with roofing nails, but my question is, do I have to let the flange in to the studs so it's flush to the studs, to allow the green board to float over the flange nicely? We are tiling the surround area. Thanks for any help. I am currently setting my stringers for the support right now as I type. Here is a link to the tub, Bootzcast Bath Tub
