Jump to content
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble
kmealy

TGIF: Finishing Fixtures #8 - Paper Tuesday Jan 13, 2018

Rate this topic

Recommended Posts

You get a large roll of paper, sometimes called "red rosin paper" or "builder's paper" to put underneath your finishing to catch drips and overspray.   If you want to get really fancy, you can make a little roller to fit under the edge of your work table and/or a cutoff edge on the opposite edge (I'm not there yet).     Another option, if you have a source is large cardboard boxes (think appliance boxes) that you can open up and lay on the floor to protect it from stripper, stain,  solvents, and finishes (this I do have).

 

IMG_9917.JPG.ede5aeabb8f07f83e0202c25e61bea26.JPG

Edited by kmealy

Share this post


Link to post
Share on other sites

Having a roll of rosin paper around is a must for shops, IMHO. It has all sorts of uses including the one you described.

Share this post


Link to post
Share on other sites

Rosin paper? New one on me. Big box stores...other than those scarce  Menards...carry it?

Edit: never mind, I found it at several places. Thanks for the tip.

Edited by Gene Howe

Share this post


Link to post
Share on other sites
1 hour ago, Fred W. Hargis Jr said:

Having a roll of rosin paper around is a must for shops, IMHO. It has all sorts of uses including the one you described.

I've used it for patterns and for full-scale drawings.   Good to catch glue drips on large panel glue ups.   Right now, I'm putting finish on a 15 light door, each piece of glass has some taped on to keep the glaze and finish off.   Put it on the floor for messy remodeling work (drywall, tiling, plumbing, etc.)  What else, Fred?

 

 

Share this post


Link to post
Share on other sites

That's the big stuff for me...one other thing I do is use it when I flatten/soften veneer. The usual method is to clamp it flat between platens and kraft paper after you sprayed it with the appropriate solution, I just use the rosin paper. I have in the past drawn patterns on plywood since I didn't have paper that was large enough....but the rosin paper is much better. The drywall guys that did the mudwork on my shop completely covered the floor with it to keep the mud from sticking to the concrete. I asked them to leave it so I could paint, in retrospect I'm not sure that was a good idea...picking up and disposing of that much rosin paper was a bit of a chore.

Share this post


Link to post
Share on other sites

I used it to make a pattern for the vinyl floor in my downstairs bathroom remodel - the room was a little out-of-square plus had a couple of jogs. Actually had to take it and the sheet of flooring out and lay it on the back deck as that was the only open space I had that was large enough to hold it.

 

Another handy item to make small templates is paper joint tape as it's pretty stiff. I used it to make a pattern when I was wrapping the sill on the back door. And for measuring the angle on the molding for the door glass.

IMG_1948.JPG

IMG_1950.JPG

IMG_1952.JPG

IMG_1960.JPG

IMG_3834.JPG

IMG_3838.JPG

IMG_3832.JPG

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Who We Are

Operation Ward 57 Challenge Coin Display Project

We are a woodworking community with an emphasis on sharing and learning the skilled craft of woodworking and all of its related disciplines. Our community is open to everyone who wishes to join us. We support our American veterans and active duty, being a veteran is not a prerequisite to join. Join us now!

Objective

Air Force Command Center Plaque

Of course just like most online woodworking communities we are centralized in the arts, crafts, and trades that are woodworking. But, we have another focus in our Patriot Woodworker community, we are the only woodworking community that was founded on our care and concern for our disabled veterans.

Volunteer

Patriot Woodworker Volunteers

The Patriot Woodworkers are an all volunteer community, from the staff and hosts who run our online woodworking community to the members who frequent our forums, you'll find volunteers in all of us. We are not on a payroll, unless you consider the spiritual rewards gained from volunteering, as compensation.

Education

Logging

One of the many projects we are working on is a wiki for our online community. A wiki is a great way for woodworkers and enthusiasts to share their knowledge to others, and to impart their knowledge for others to learn from, and utilize as well for their own benefit. We hope you'll consider being a wiki contributor.

×