Jump to content
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble

Rate this topic

Recommended Posts

While building a new router wing for my tablesaw, I realized I used a template for my old router plate.....,perfect. Whelp, I  ain’t getting those two hours back!

5DD73BA3-31AC-4539-8B38-4D70C8DF2D91.jpeg

Share this post


Link to post
Share on other sites

Your gonna have to have some long arms to use that. How far past the end of the picture does it go?

Share this post


Link to post
Share on other sites

Just looks long b/c I didn’t Cut the miter track dado yet. Same  distance in front of the bit as  a Rockler router table. But I don’t have to worry about that stupid miter track cuz I  gotta a toss the thing! 

Share this post


Link to post
Share on other sites

I'm laughing with ya Dane, not at you! :D I feel yer pain!

Share this post


Link to post
Share on other sites

That side never gets used anyway. Your fence should cover it up. If it were mine I would leave it to remind myself to check all measurements and sizes before cutting anything....

Share this post


Link to post
Share on other sites

Well Bummer Dane...fit really nice on three sides:P

Don't cha' just hate Mondays on both sides of the weekend?:rolleyes:

At least you're able to do something in your shop; got me beat.

 

Share this post


Link to post
Share on other sites

I'd be reaching for the Bondo. As Jesse said, the fence will cover it anyway.

Edited by Gene Howe

Share this post


Link to post
Share on other sites
1 hour ago, Grandpadave52 said:

Well Bummer Dane...fit really nice on three sides:P

Don't cha' just hate Mondays on both sides of the weekend?:rolleyes:

At least you're able to do something in your shop; got me beat.

 

I had a woodpecker router plate and  it’s like inch and three-quarter longer than  rockler one. I made a jig for the old router saw  wing -and use that  on this new wing. Too bad plates are  standardized ......

Share this post


Link to post
Share on other sites

Flip it over and try it again?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Who We Are

Operation Ward 57 Challenge Coin Display Project

We are a woodworking community with an emphasis on sharing and learning the skilled craft of woodworking and all of its related disciplines. Our community is open to everyone who wishes to join us. We support our American veterans and active duty, being a veteran is not a prerequisite to join. Join us now!

Objective

Air Force Command Center Plaque

Of course just like most online woodworking communities we are centralized in the arts, crafts, and trades that are woodworking. But, we have another focus in our Patriot Woodworker community, we are the only woodworking community that was founded on our care and concern for our disabled veterans.

Volunteer

Patriot Woodworker Volunteers

The Patriot Woodworkers are an all volunteer community, from the staff and hosts who run our online woodworking community to the members who frequent our forums, you'll find volunteers in all of us. We are not on a payroll, unless you consider the spiritual rewards gained from volunteering, as compensation.

Education

Logging

One of the many projects we are working on is a wiki for our online community. A wiki is a great way for woodworkers and enthusiasts to share their knowledge to others, and to impart their knowledge for others to learn from, and utilize as well for their own benefit. We hope you'll consider being a wiki contributor.

×