Larry Buskirk Posted August 3, 2015 Report Share Posted August 3, 2015 You got your BS running much faster than I did. My little 785 Delta is still a WIP, has been for almost 3 years. Quote Link to comment Share on other sites More sharing options...
stevem Posted August 3, 2015 Author Report Share Posted August 3, 2015 well I was busy over the winterrebuilt and sold a beaver 3300(bandsaw) and a 3800(jointer), bought and rebuilt a craftmaster 12inch bandsaw, and that's just the beginning, plus a wheatley jointer, another beaver lathe, repowered the craftmaster lathe, sold a beaver 3700 and bought another, you know typical Canadian winter in ontariosomewhere in there I also went to work, built some furniture etc etc Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted August 3, 2015 Report Share Posted August 3, 2015 well I was busy over the winter rebuilt and sold a beaver 3300(bandsaw) and a 3800(jointer), bought and rebuilt a craftmaster 12inch bandsaw, and that's just the beginning, plus a wheatley jointer, another beaver lathe, repowered the craftmaster lathe, sold a beaver 3700 and bought another, you know typical Canadian winter in ontario somewhere in there I also went to work, built some furniture etc etc Steve, Is that all? Now I really feel like a slouch. Quote Link to comment Share on other sites More sharing options...
stevem Posted August 4, 2015 Author Report Share Posted August 4, 2015 here's an idea of the scope of the body work remember that was built during the first world war, cosmetics was not a high priority for manufacturing equipment Quote Link to comment Share on other sites More sharing options...
stevem Posted August 4, 2015 Author Report Share Posted August 4, 2015 well im pleased to say that the old crescent works well, actually has been for several months, the guards are new. I did havbe some issues with bearings getting too warm, resolved that with 30w non detergent motor oil, is does require oil regularly, I add a couple of drops everyday that I use it. the lower shaft is babbitt, the upper is a steel shaft on cast iron. the hex hole for the guide post and the table tilt quadrant are also babbittI have resawn 8 inch white oak and walnut, no issues except the fence system(1940's beaver). it is far easier to snap a chalkline and follow the line than mess around with fencesthe jointers are next, got a beaver 3800(6 inch), wheatley (6 inch) and a beaver/rockwell 4 inch. the beaver 3800 is my regularly user, the little 4 inch has a very high angle grind, great for small pieces of figured woods Quote Link to comment Share on other sites More sharing options...
stevem Posted August 4, 2015 Author Report Share Posted August 4, 2015 well maybe not, i'll continue on with the various bandsaws ive rebuilt first is the beaver 3300, its a 14 inch, same as the common as mud delta and all of its clones, but this one is different the entire frame/body is a one piece cast aluminum, 4feet tall. the callander foundry boys must have learnt a lot during WW11 ive done several of these, nice machine, easy rebuild unless the wheels get loose from the axle and start to wobble next is the beaver 2300, an allcast iron 12 inch saw, quite rare for some reason, nice little saw thent here's the henry power tools craftmaster, this was rebadged and sold by portercable in the states. mine was found in a dumpster behind a habitat for humanity store sharp eyes may notice the craftmaster lathe on the shelf above the bandsaw all these saws were rebuilt and sold except the last one, just finished it Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted August 4, 2015 Report Share Posted August 4, 2015 here's an idea of the scope of the body work remember that was built during the first world war, cosmetics was not a high priority for manufacturing equipment Most of my 1930's Delta's required their share of it too. I love the smell of Bondo, it smells like victory! Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted August 4, 2015 Report Share Posted August 4, 2015 well maybe not, i'll continue on with the various bandsaws ive rebuilt first is the beaver 3300, its a 14 inch, same as the common as mud delta and all of its clones, but this one is different the entire frame/body is a one piece cast aluminum, 4feet tall. the callander foundry boys must have learnt a lot during WW11 ive done several of these, nice machine, easy rebuild unless the wheels get loose from the axle and start to wobble next is the beaver 2300, an allcast iron 12 inch saw, quite rare for some reason, nice little saw thent here's the henry power tools craftmaster, this was rebadged and sold by portercable in the states. mine was found in a dumpster behind a habitat for humanity store sharp eyes may notice the craftmaster lathe on the shelf above the bandsaw all these saws were rebuilt and sold except the last one, just finished it I like the lines of the "Beavers". Even though they were sold through Montgomery Wards, we don't see many of them this side of the border. Quote Link to comment Share on other sites More sharing options...
stevem Posted August 4, 2015 Author Report Share Posted August 4, 2015 Most of my 1930's Delta's required their share of it too. I love the smell of Bondo, it smells like victory! yeah it reminded me of the 1970 Datsun that I had, less rust of course on the crescent Quote Link to comment Share on other sites More sharing options...
stevem Posted August 4, 2015 Author Report Share Posted August 4, 2015 many of the beavers were available stateside from MW, and some of the craftmaster stuff was available rebadged from porter cable. the entire line was adopted and sold by fosters in the us, some were repainted, rebadged and sold by general of quebec Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted August 4, 2015 Report Share Posted August 4, 2015 yeah it reminded me of the 1970 Datsun that I had, less rust of course on the crescent.Recycled rust vs. virgin iron.You'd actually be surprised how much body filler is used on new vehicles, they don't use lead anymore. Quote Link to comment Share on other sites More sharing options...
John Moody Posted August 6, 2015 Report Share Posted August 6, 2015 Both of the Bandsaws are great looking. Nice restorations! Quote Link to comment Share on other sites More sharing options...
Jonel Vukan Posted August 7, 2015 Report Share Posted August 7, 2015 Very nice restorations. It is a very slippery hobby. I started my old iron addiction by trying to put together a wood working shop. Now I have 4 tables saws, 2 band saws , 4 drill presses etc. Enjoy it. Quote Link to comment Share on other sites More sharing options...
stevem Posted August 7, 2015 Author Report Share Posted August 7, 2015 well next is the jointers or maybe the tablesaw Quote Link to comment Share on other sites More sharing options...
stevem Posted August 9, 2015 Author Report Share Posted August 9, 2015 (edited) well the tablesaw is kinda hohum, just another delta tilttop, at least its not just another unisaw!! so the jointers.my regular user is a 6 inch beaver 3800 this an older picture, it has a small (Leland)1/2 hp ri motor under the outfeed table, its been upgraded to a 1 hp ri century monster on the other side. has to run on 240, the motor draws 15 amp on 120 i'll get a new picture or two tomorrow. the 3800 is really unique, there is no spindle, the cutterhead with intregal pulley is mounted in tapered roller bearings, the fence system is a study in walter mitty complexity I have other jointers as well, but the beaver is my favourite. note the beaver cast iron leg stand Edited August 9, 2015 by stevem Quote Link to comment Share on other sites More sharing options...
stevem Posted August 9, 2015 Author Report Share Posted August 9, 2015 heres a utube video of the 3800 in action with the 1hp century ri its a beast, unstoppable 007.AVI Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted August 10, 2015 Report Share Posted August 10, 2015 (edited) well the tablesaw is kinda hohum, just another delta tilttop, at least its not just another unisaw!! & Edited August 10, 2015 by Larry Buskirk Quote Link to comment Share on other sites More sharing options...
stevem Posted August 12, 2015 Author Report Share Posted August 12, 2015 here's my little beaver jointer, 4 inch. I keep this machine setup for highly figured woods, the knives have been honed very careful it will joint birds eye maple very nicely Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted August 13, 2015 Report Share Posted August 13, 2015 here's my little beaver jointer, 4 inch. I keep this machine setup for highly figured woods, the knives have been honed very careful it will joint birds eye maple very nicely Steve, How many parts does that share with its Homecraft 37-110 counterpart? Other than the badges they look identical. Quote Link to comment Share on other sites More sharing options...
stevem Posted August 14, 2015 Author Report Share Posted August 14, 2015 im not sure larry, but they look virtually identical, this is a 2801. there was a previous much heaver 4 inch machine, the 2800not surprising really, Rockwell bought the callander foundry in Guelph, ontario and the beaver tool line in 1954some of the beaver designs were kept and some replaced with rockwells Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.