Cal Posted December 21, 2020 Report Share Posted December 21, 2020 Now how cool is that Kevin! Did you also glue up the walnut flower into the maple blank? Please be sure to post up a few more pips Gunny, HARO50 and FlGatorwood 3 Quote Link to comment Share on other sites More sharing options...
Popular Post Kevin Beitz Posted December 21, 2020 Author Popular Post Report Share Posted December 21, 2020 Yep... I did both... Can't wait until the glue dries so I can sand them down... When sanding's done I will wood burn the details in... p_toad, Larry Buskirk, Gunny and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Popular Post Kevin Beitz Posted December 22, 2020 Author Popular Post Report Share Posted December 22, 2020 I knew the glue was going to give the belt sander a fit so I slapped the project in the milling machine. Gunny, Larry Buskirk, FlGatorwood and 2 others 5 Quote Link to comment Share on other sites More sharing options...
Popular Post Kevin Beitz Posted December 22, 2020 Author Popular Post Report Share Posted December 22, 2020 Not to bad... Gunny, FlGatorwood, Larry Buskirk and 2 others 5 Quote Link to comment Share on other sites More sharing options...
Kevin Beitz Posted December 22, 2020 Author Report Share Posted December 22, 2020 A little wood burning.... HARO50, FlGatorwood, Gunny and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Popular Post Kevin Beitz Posted December 22, 2020 Author Popular Post Report Share Posted December 22, 2020 First coat... Cal, Larry Buskirk, HARO50 and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Gunny Posted December 22, 2020 Report Share Posted December 22, 2020 Awesome FlGatorwood, Larry Buskirk and Cal 3 Quote Link to comment Share on other sites More sharing options...
Popular Post Kevin Beitz Posted December 22, 2020 Author Popular Post Report Share Posted December 22, 2020 HARO50, Gunny, Cal and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Gunny Posted December 22, 2020 Report Share Posted December 22, 2020 49 minutes ago, Kevin Beitz said: Cal, Larry Buskirk and FlGatorwood 3 Quote Link to comment Share on other sites More sharing options...
Kevin Beitz Posted December 24, 2020 Author Report Share Posted December 24, 2020 I'm having a hard time with the varnish... I keep sanding it down and recoating but I'm not happy with the finish... Larry Buskirk, Cal, FlGatorwood and 2 others 1 4 Quote Link to comment Share on other sites More sharing options...
Smallpatch Posted December 24, 2020 Report Share Posted December 24, 2020 Kevin those are looking good but I would have used lacquer and you could have been finished with those and gone back to the scrap yard for more goodies.! Harry Brink, Cal and Gunny 2 1 Quote Link to comment Share on other sites More sharing options...
Kevin Beitz Posted December 25, 2020 Author Report Share Posted December 25, 2020 Thanks... I'll try that next time... FlGatorwood, Gunny and Cal 3 Quote Link to comment Share on other sites More sharing options...
Cal Posted December 25, 2020 Report Share Posted December 25, 2020 Looking good there Kevin. FlGatorwood and Larry Buskirk 2 Quote Link to comment Share on other sites More sharing options...
Smallpatch Posted December 25, 2020 Report Share Posted December 25, 2020 Kevin after you get the board flat by sanding and before any finish is applied you need to use a filler to bring all the surface up to the same height....your filler should be as close to the same appearance as the surrounding areas being filled. If you use shellac or lacquer they both will show all the flaws so this is a have to do if you want a specimen to show off... The worse part is if you used a wide blade in the scroll saw then any gap will show up whether it has been filled flat like all the rest of the area or not....So good luck.......... Cal 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Kevin Beitz Posted December 25, 2020 Author Popular Post Report Share Posted December 25, 2020 The gaps I got even with the smallest blade. I needed to make very sharp turns and I had to make room for the blade to turn. This is why I was using varnish. I taped up the bottom to stop the runs and fill the cracks. I could have used epoxy. Any better ideas? One trick I've used over the years was to rub the sanding dust back into the cracks before I varnished. This worked best years ago when I sanded my grandfathers kitchen floor. It looked great until I vacuumed up all the dust. I had some floor cracks 1/2" wide. I dumped the sanding bag is dust back onto the floor and swept it all back in the cracks. Then I took sanding sealer to the whole floor. After It dried I sanded again. Then I varnished. Turned out great. FlGatorwood, Cal, Larry Buskirk and 2 others 5 Quote Link to comment Share on other sites More sharing options...
Gunny Posted December 25, 2020 Report Share Posted December 25, 2020 Some epoxy and you are good. I have used the sawdust trick and had it give me issues sometimes. Epoxy, never a problem. FlGatorwood, JimM, Cal and 1 other 4 Quote Link to comment Share on other sites More sharing options...
FlGatorwood Posted December 26, 2020 Report Share Posted December 26, 2020 If it is a tiny crack, mix some wood glue and mix in sanding dust. Ensure you get more dust on top which will stick to the glue down in the crevice so when you finish, the dust will act as wood. Otherwise, you get glue showing and then it is hard to stain. Gunny, Cal, JimM and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Kevin Beitz Posted December 28, 2020 Author Report Share Posted December 28, 2020 Better finish on these two... FlGatorwood, DuckSoup and Cal 3 Quote Link to comment Share on other sites More sharing options...
Cal Posted December 28, 2020 Report Share Posted December 28, 2020 Very cool work Kevin. FlGatorwood 1 Quote Link to comment Share on other sites More sharing options...
Smallpatch Posted December 28, 2020 Report Share Posted December 28, 2020 Now your talking Kevin. Its easy to see the difference in those finishes. If you want to go the next step after the finish has dried good take 0000 steel wool with some Johnsons paste wax and go over it all with a good rubbing. Cal, DuckSoup and FlGatorwood 3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.