Popular Post Fred W. Hargis Jr Posted October 12, 2019 Popular Post Report Share Posted October 12, 2019 I had mentioned in another post I was building a desk. This isn't anything really challenging but I want to prove I'm doing something. I need 2 of these, one for a basement area I use and another for our main floor "office". I was planning on doing both in an A&C style, but I now think the second one will be more contemporary. The reason why is that both are computer desks, and I want/need a drop down drawer front for a keyboard tray. The A&C style with inset drawers just doesn't lend itself to that convention. In the pics below you can see the drawer opening...since I don't have a way to hinge the front down (with hidden hinges, and it stay level when opened) I'm thinking it will just be removable, held in place with spring clips. Then the keyboard tray will just pull out. Anyway, I mentioned a week or so ago I had these wide oak boards I would be using. They were supposed to be white oak, turns out all but the one on the left is red oak. I don't like red oak, and never use it...much preferring the white species. But I have what I have, so I went and bought some more red oak to complete the desk, and you can see the dry fitted frame. Nothing remarkable here, but I did do every joint with loose tenons and that worked out OK. Cal, Artie, LarryS and 6 others 9 Quote Link to comment Share on other sites More sharing options...
Popular Post Larry Buskirk Posted October 12, 2019 Popular Post Report Share Posted October 12, 2019 Fred, A bit late but, if you backset the lower brace below the drawer opening you can do the inset drawer with a drop front. FlGatorwood, Artie, Gunny and 2 others 5 Quote Link to comment Share on other sites More sharing options...
lew Posted October 12, 2019 Report Share Posted October 12, 2019 (edited) Do you think this might work for the hinge? https://www.hafele.com/us/en/product/desk-pivot-hinge-90-opening-angle/000000000001459300010023/ Nice build! Edited October 12, 2019 by lew FlGatorwood, Cal and Artie 3 Quote Link to comment Share on other sites More sharing options...
Fred W. Hargis Jr Posted October 12, 2019 Author Report Share Posted October 12, 2019 (edited) Lew, I think that one would work...it is really way too long. It's 5 7/8", and my drawer front is only 2 1/2". Still, I'll bet I could cut it down and make it work...I may try a set. Larry it's not too late, I can make a new front rail easily. Edited October 12, 2019 by Fred W. Hargis Jr HARO50, Artie, FlGatorwood and 1 other 4 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted October 12, 2019 Report Share Posted October 12, 2019 Did you cut the flip down out of the same piece as the front? Cal and FlGatorwood 2 Quote Link to comment Share on other sites More sharing options...
Larry Buskirk Posted October 12, 2019 Report Share Posted October 12, 2019 4 minutes ago, Fred W. Hargis Jr said: Larry it's not too late, I can make a new front easily. You could also just cut out the lower brace at the sides, and backset a longer piece behind the front. Cal and FlGatorwood 2 Quote Link to comment Share on other sites More sharing options...
Fred W. Hargis Jr Posted October 12, 2019 Author Report Share Posted October 12, 2019 (edited) Jack, that's what I did, the front rail was ripped into 3 pieces, then the center piece had the drawer front removed; then I glued everything back together. Edited October 12, 2019 by Fred W. Hargis Jr HARO50, FlGatorwood and Cal 3 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted October 12, 2019 Report Share Posted October 12, 2019 5 minutes ago, Fred W. Hargis Jr said: Jack, that's what I did, the front rail was ripped into 3 pieces, then the center piece had the drawer front removed; then I glued everything back together. Perfect........... FlGatorwood and Cal 2 Quote Link to comment Share on other sites More sharing options...
Popular Post Fred W. Hargis Jr Posted October 12, 2019 Author Popular Post Report Share Posted October 12, 2019 OK, I was chasing those hinges Lew linked above and came up with something else. It's this one and the installation could be made to work and do exactly what I want. It's a little deep to install into a 3/4" rail, but I can glue some extra wood to the back of the rail to accommodate it. Cal, LarryS, HARO50 and 3 others 6 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted October 12, 2019 Report Share Posted October 12, 2019 Solid white oak top? Break board? Cal and FlGatorwood 2 Quote Link to comment Share on other sites More sharing options...
Popular Post Fred W. Hargis Jr Posted October 12, 2019 Author Popular Post Report Share Posted October 12, 2019 No, the tops will be 2 of the wide red oak boards in the pic above. I just finished planing them, they dressed at 7/8" thick and they actually have a good color and grain match. I bought those boards a long time ago, need to use them up. FlGatorwood, Gunny, Cal and 2 others 5 Quote Link to comment Share on other sites More sharing options...
lew Posted October 12, 2019 Report Share Posted October 12, 2019 38 minutes ago, Fred W. Hargis Jr said: OK, I was chasing those hinges Lew linked above and came up with something else. It's this one and the installation could be made to work and do exactly what I want. It's a little deep to install into a 3/4" rail, but I can glue some extra wood to the back of the rail to accommodate it. I like these better. No mods necessary. Fred W. Hargis Jr, FlGatorwood and Cal 2 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Fred W. Hargis Jr Posted October 12, 2019 Author Popular Post Report Share Posted October 12, 2019 Well, I went ahead and got the boards for the top ready. These are from those ones in the first pic, adn are big enough for the top on this desk (60"x28"). Jointing these things was an adventure, I should have had Newman show me how to joint a board with a hand plane...would have been easier. This desk is going to be 2-dog ugly (I hate red oak, especially flat sawn) but I'm the only one who will see it (and it replaces a Sauder RTA desk!) Cal, p_toad, Artie and 5 others 8 Quote Link to comment Share on other sites More sharing options...
Popular Post lew Posted October 12, 2019 Popular Post Report Share Posted October 12, 2019 1 minute ago, Fred W. Hargis Jr said: I hate red oak, especially flat sawn Around here, every church you go into is predominantly flat sawn red oak. I guess we just get used to it. Cal, LarryS, HARO50 and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Gerald Posted October 12, 2019 Report Share Posted October 12, 2019 4 minutes ago, lew said: Around here, every church you go into is predominantly flat sawn red oak. I guess we just get used to it. Funny you say that . When our church was remodeled two years ago they did the same thing and stained it a dark stain which makes the grain stand out and I hate it. Plus they did the pulpit in it instead of using quartersawn I just do not like it and like Fred I do not like red oak and especially do not like to turn it. I got part of the scheme changed by using pecan for offering plates but then they wanted it stained , just can't win. Artie, Gunny, Cal and 3 others 2 4 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted October 12, 2019 Report Share Posted October 12, 2019 36 minutes ago, Fred W. Hargis Jr said: Well, I went ahead and got the boards for the top ready. These are from those ones in the first pic, adn are big enough for the top on this desk (60"x28"). Jointing these things was an adventure, I should have had Newman show me how to joint a board with a hand plane...would have been easier. This desk is going to be 2-dog ugly (I hate red oak, especially flat sawn) but I'm the only one who will see it (and it replaces a Sauder RTA desk!) Sometimes it pays to mill the boards down to about 4" or so. Wide boards don't generally do to well.. FlGatorwood and Cal 2 Quote Link to comment Share on other sites More sharing options...
Fred W. Hargis Jr Posted October 12, 2019 Author Report Share Posted October 12, 2019 Yeah, it's a good point, especially with flat sawn stock. I may well wind up regretting not ripping them and glue back together. Cal, FlGatorwood and Gunny 3 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted October 12, 2019 Report Share Posted October 12, 2019 Sometimes it's fine. Just depends on how you set up for it... FlGatorwood and Cal 2 Quote Link to comment Share on other sites More sharing options...
Popular Post Larry Buskirk Posted October 12, 2019 Popular Post Report Share Posted October 12, 2019 Well Fred, I'm sure it will look better than the "Sauder" press board with paper wood grain it replaces. LarryS, HARO50, Cal and 3 others 5 1 Quote Link to comment Share on other sites More sharing options...
DuckSoup Posted October 12, 2019 Report Share Posted October 12, 2019 That's one hefty looking desk Fred. Fred W. Hargis Jr, FlGatorwood, Cal and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.