Jump to content
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble
Dadio

Dust Collection on RE Saw

Rate this topic

Recommended Posts

I do like that, I'm guessing you keep your saw at 90º?

Share this post


Link to post
Share on other sites
30 minutes ago, Fred W. Hargis Jr said:

I do like that, I'm guessing you keep your saw at 90º?

Yeah I do, Fred,

I use it exclusively for 90 deg.  cut offs. I hate to cut off long boards on the table saw.  I do the miter cuts on the TS.  Not doing any long material miter cuts any more, if I cut long stuff, like rafters etc. I do it out side on saw horses  and a chop saw or skill saw.

Also I might add I cut wedges and lay them on the table sometimes to make the angle either up and down, or flat,thus keeping the blade at 90 deg. to the fence.

Herb

Edited by Dadio

Share this post


Link to post
Share on other sites

That is an awesome design Herb. I really like it/

My RA needs a new top anyway so you've inspired me.

It'll be a while but I will give my best effort to come half way close to this.

It appears the insert is  replaceable/removable/changeable as needed. Very cool!

THANKS for sharing!

Share this post


Link to post
Share on other sites

Herb, this is great.   I have the same saw and use for crosscuts only as well.   What did you do under the saw?   Im assuming just enclosed the metal support frame?

Share this post


Link to post
Share on other sites
1 hour ago, Wil said:

Herb, this is great.   I have the same saw and use for crosscuts only as well.   What did you do under the saw?   Im assuming just enclosed the metal support frame?

Wil, the Metal channel saw frame sets on a 3/4" plywood top which is lower than the long off feed top of the bench,(Was Made for a Chop Saw Originally). On top of the metal saw channel is another piece of 3/4" ply to bring it up to height. Then the final layer is a removable top so it can be replaced if it gets beat up. In the 2nd picture you can see the replaceable top and the sub top.

I made a couple of extra inserts when I made the one shown, just in case I later want to replace it. The hole in the insert is a finger hole to pull it out , the reason I used a T/G is I didn't want any metal fasteners in proximity of the blade.

As I said before ,this set-up seems to capture 90+% of the sawdust. I added a couple of holes in the side of the box to add make-up air since I have plenty of air flow and it keeps the airflow in the main duct up without choking it down.

Herb

Share this post


Link to post
Share on other sites

I got a new table and blade guard for a Craftsman RA saw through their recall at no cost.

Share this post


Link to post
Share on other sites

well done Mr. Thinker...

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Who We Are

Operation Ward 57 Challenge Coin Display Project

We are a woodworking community with an emphasis on sharing and learning the skilled craft of woodworking and all of its related disciplines. Our community is open to everyone who wishes to join us. We support our American veterans and active duty, being a veteran is not a prerequisite to join. Join us now!

Objective

Air Force Command Center Plaque

Of course just like most online woodworking communities we are centralized in the arts, crafts, and trades that are woodworking. But, we have another focus in our Patriot Woodworker community, we are the only woodworking community that was founded on our care and concern for our disabled veterans.

Volunteer

Patriot Woodworker Volunteers

The Patriot Woodworkers are an all volunteer community, from the staff and hosts who run our online woodworking community to the members who frequent our forums, you'll find volunteers in all of us. We are not on a payroll, unless you consider the spiritual rewards gained from volunteering, as compensation.

Education

Logging

One of the many projects we are working on is a wiki for our online community. A wiki is a great way for woodworkers and enthusiasts to share their knowledge to others, and to impart their knowledge for others to learn from, and utilize as well for their own benefit. We hope you'll consider being a wiki contributor.

×