Jump to content

Rate this topic

Recommended Posts

Didn't even wait for Lunch....

The other 4 panels have been "raised"

5980d05b4e504_panelsandrails.jpg.0e5bf239fdd272d2dec153f04d8bcd40.jpg

basically the same as the others were done.   Bench is now cleaned up..

5980d0a567cfd_clearedoff.jpg.063ad92c06ffa560aac86fd21c54b301.jpg

I had to go back upstairs to get the camera....this thing came along when I came back to the shop.    Stiles are awaiting mortises to be chopped

5980d109840fb_cleanedfloor.jpg.deba9459976020f9dc678e14214bad53.jpg

Floor has been cleaned up!  (again...) Sooo, where all the stuff go?

5980d15b0def5_gluedup.jpg.5581acac3e82d322293c79866a565777.jpg

Most of the other parts went here, along with a bunch of clamps....hard to work the clamps, with a busted thumb...Side One can sit here until I need them clamps again.   Ham & Cheese on Wheat....Lunch was a tad late, today...

 Letting Lunch settle in.....maybe later a few mortises will get chopped?  Only need 8..

 

Stay tuned...

Share this post


Link to post
Share on other sites

Ok...1 x 2s have been moved down to the shop, a wee bit long to carry down there.  

 

Got the LAST three mortises chopped, and dry fitted....Removed the clamps from side #1, and "staged" them close to the bench.....

 

Glue up went about as well as can be expected.....:rolleyes:.....added an extra pipe clamp in the center.....creaks and groans...both me and the parts:o, but, no CRACK was heard:ph34r:

 

Set the mess aside, after adding a few "F" style clamps....

5981f5b4d3156_Bothsides.jpg.9d595a23c3a1765cf8e8b9a7424385f7.jpg

Able to stand up on it's own?   Well, there is a LARGE pair of Visegrips keeping the bottom pipe clamp from working loose

Looking nice?  Except...IF you look behind these two..

5981f6403f2f7_noroom.jpg.438cec579f866ae79ea0027ef4c1b47b.jpg

Need to get to the Mitre Box  ( wait..I do have a spare..) and need to get TO those 1 x 2s leaning up, back there...

 

Oh, well, I guess it could wait while the glue dries.   Need to figure how wide to make the case, so I know how wide the webframes will be. 

That will be next on the "schedule"  ...stay tuned....

Share this post


Link to post
Share on other sites

Hanging around for the next episode of "Dew It to It!"

Share this post


Link to post
Share on other sites

You must get extra adrenaline in the shop. I do. Feel terrible till I get in the shop and then full tilt until I sit down in front of the TV and collapse.

Share this post


Link to post
Share on other sites

Not to hijack your thread, but i'm afraid Natasha won't be doing any more jobs with Boris.

 

June Foray, who voiced Rocky and Natasha cartoon characters, dies at 99

Share this post


Link to post
Share on other sites

Ok,last night..went to check on the fan...whether I remembered to turn it off, or not..:ph34r:

 

Did a double check of a mortise I had laid out, but not chopped.....it was on the wrong side....compost happens:rolleyes:

So, this afternoon, I corrected that and cut a new mortise..

59851e4eeb45f_correctmortise.jpg.b8521037c1f517cb1ea2d6658a9bbc3b.jpg

Then went and finished that  frame...

59851e9547652_topframe.jpg.c49c1bfb4473e813760a8f67f074d200.jpg

Had the feeling this was going to fight the entire way.   Large holes?   So I can attach the frames to the sides of the case....much easier to forstner bit and pilot drill when stuff isn't in the way..DAMHIKT....Another "issue" was screws to hold the kickers in place....Countersink wasn't  working right, some of the screws were way too long.

59851f71aeec5_doublekickers.jpg.1cdd30ff7b22a4301256e2373068cbc2.jpg

The screws that were too long?  took them back out and ground off the excess. Two kickers for the two drawers.   This one is the top frame...only the top of case is above it.   Clamped and glued up, and set aside..

 

Saw  work...

backsaw.jpg.c9ee2f7015e509c360acfbcc81a02f17.jpg

This is the angle used, to make the cut..

598520b266bb7_sawcut.jpg.12cb49d507b08c77140d0ea42800c90a.jpg

To cut the sides of the mortise.  Then a bit of work with the chisel..

chopping.jpg.89750b5d69b457bcbb238c9534e2f362.jpg

And dig a hole at the far end.   Lay the chisel flat, as to pare, and pop the waste right out.   Clean things up and do a dry fit, or three,,

598521a12dd32_dryfit.jpg.244f58e9a8f14e690d4a21bdb150bd77.jpg

And another short rail is fitted.    About these short rails....all were cut from a 1 x2 x8' board.....not the best looking ones, either..

5985221197069_squarethumb.jpg.3f0e29bf69e94e2ed99ad335c0d7d5e8.jpg

And some were a hair wider than others...we have ways..(yep, that is my sore thumb..)

5985226786c4a_jackplane.jpg.db38e8d2b2c6e141b04bff5cba35f88e.jpg

Ok, got them all squared up ( one even had a twist to it) and close to the same size....I chucked the Forstner bit into the drill press ( cordless didn't spin fast enough) and made a few holes..

5985230da8164_pilotholes.jpg.ce1fa5c369161229249211e1fc9db44c.jpg

Counter-bores, then a drill bit to make the pilot holes.  Rather do these now, than try it went things are all glued up.   All I needed was two holes per rails.   Allowed a space for the drill to get in and drive some screws...

598523ca1fcf2_singlekickerframe.jpg.d37d0b81e02f9758a5cccca868b95bed.jpg

I have had to trim just under an 1/8" off the ends of these kickers....must have cut on the wrong side of the lines...Oh well.:rolleyes:

I was going to try and get all the frames done, today.....ran out of those type of clamps.....pipe clamps would have been just too much.:unsure:

Called it a day, and let the glue dry....tomorrow, I can get the last two frames done....maybe. 

 

Stay tuned to this Bat Channel.....

Edited by steven newman (see edit history)

Share this post


Link to post
Share on other sites

Whew! I can't imagine how much you'd get done if your thumb was banged up and you weren't documenting the build along the way!:P I thought I accomplished a lot today, but I think you still out did me...

I gotta start drinking more Mountain Dew!:lol:

Share this post


Link to post
Share on other sites

Looking great so far and really taking shape. You've made some amazing things since I've been on-board here, but I think you're about to outdo yourself on this one...

And you sure ain't been all thumbs on it either!:lol:

Share this post


Link to post
Share on other sites

Sorry to hear about your friend.

Share this post


Link to post
Share on other sites
1 hour ago, lew said:

Sorry to hear about your friend.

Lew: you MIGHT know him as well.   Eddie, from the Stumpy Nubs group over on LJs.   Eddie was the one I received those puppies from.   He was 62

 

Gene also knows him.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


About us

We are a woodworking community with an emphasis on sharing and learning the skilled craft of woodworking and all of its related disciplines. Our community is open to everyone who wishes to join us. We support our veterans and active duty both here in the United States and in Canada, being a veteran is not a prerequisite to join. So please, join us! Please click on Join The Patriot Woodworker's.

 

We support MWTCA, preserving tools and implements from the past.

M-WTCA Logo.gif

Get in touch

Follow us

Recent tweets

Visit us on Facebook

×